Diyvehiclerepair
The kick down cable is mounted to the carburetor, or, in the case of fuel injected vehicles, the throttle body. It runs from the butterfly arm on the carburetor down to the side of the transmission, where it attaches to an arm that allows the transmission to shift gears.
- What happens when a kickdown cable goes bad?
- Can you drive without a kickdown cable?
- Is a kickdown cable necessary?
- What is a transmission kickdown cable?
- Where is the kickdown cable located?
- Does a TH400 have a kickdown cable?
- Does a Turbo 350 have a TV cable?
- What is kickdown switch?
- Do you have to hook up the kickdown cable th350?
- How does a Turbo 350 kickdown cable work?
- How do I turn off kickdown cable?
- How do I install Lokar kickdown cable?
What happens when a kickdown cable goes bad?
However it can also be caused by a faulty or worn out kickdown cable. If the cable is not engaging or is slipping, then it will be very hard to produce a smooth gear change when needed. The cable can be damaged due to aggressive driving where the automatic transmission makes multiple up and down shifts.
Can you drive without a kickdown cable?
Shouldn't be a problem. The cable adjusts system pressure, so shift pressure. With the cable fully retracted it will shift lazy/slip a lot, if the cable was pulled fully out it will shift more firmly, less slip.
Is a kickdown cable necessary?
In fact, if you don't mind downshifting manually with the shift lever when passing, there's really no need for a functional kickdown cable or switch at all. ... On transmissions designed around a TV cable, its presence is mandatory.
What is a transmission kickdown cable?
The transmission kick down cable works to shift the transmission to a higher gear automatically when the engine is revved or otherwise accelerated. A kick down cable comes installed standard on any vehicle, but there are also a variety of aftermarket kick down cables that can be purchased as well.
Where is the kickdown cable located?
The kick down cable is mounted to the carburetor, or, in the case of fuel injected vehicles, the throttle body. It runs from the butterfly arm on the carburetor down to the side of the transmission, where it attaches to an arm that allows the transmission to shift gears.
Does a TH400 have a kickdown cable?
Instead of a linkage or cable, the TH400 uses an electrical switch that is most often mounted on the carburetor. ... The factory used a switch located on the carburetor or on the throttle linkage under the dash that at WOT supplied voltage to the transmission.
Does a Turbo 350 have a TV cable?
The TV cable is attached on one end to the throttle linkage and on the other end to the transmission. As the throttle is depressed, the cable is pulled, causing progressively later upshifts at higher throttle positions.
What is kickdown switch?
An electrical switch that is used to cause a transmission to downshift from a higher to a lower gear ratio.
Do you have to hook up the kickdown cable th350?
Premium Member. The kickdown is just a way to downshift with your foot (what we used to call, "passing gear"). If it's not hooked up, you just manually downshift.
How does a Turbo 350 kickdown cable work?
The kickdown function of General Motors vehicles equipped with the Turbo 350 automatic transmission is perhaps better known as "passing gear." As the accelerator is depressed, the throttle lever on the engine is drawn back by a cable, which in turn pulls another cable attached to the transmission, causing it to ...
How do I turn off kickdown cable?
Step 6: Disconnect the kickdown cable from the transmission hook. With the retaining bolt removed, gently pull up on the kickdown cable to expose the linkage that the cable is connected to. Twist the end of the kickdown cable to disengage it from the linkage.
How do I install Lokar kickdown cable?
Slide the kickdown cable end stop onto the inner wire. Move the throttle to wide open and hold it there while pulling the kickdown inner wire as tight as possible. Slide the cable end stop up against the kickdown throttle body fitting and tighten the set screw using the supplied 5/64" Allen wrench.
