Where is the throttle body located on a 97 k2500 7.4 Suburban?

1. Where is the throttle body position?
2. What are the symptoms of a dirty throttle body?
3. Is the throttle body sensor part of the throttle body?
4. How do you reset a throttle body?
5. Can you clean throttle body without removing it?
6. Does seafoam clean throttle body?
7. Will a bad throttle body throw a code?
8. What can cause a throttle body to go bad?
9. What causes an electronic throttle control to go bad?
10. What happens when you unplug throttle position sensor?
11. How do I reset my Chevy throttle body?
12. How do you relearn a Nissan throttle body?

Where is the throttle body position?

The throttle body is a circular valve that's located in between your air filter and Intake Manifold.

What are the symptoms of a dirty throttle body?

When the throttle body gets dirty, it has a direct effect on how smoothly the engine operates. Signs indicating a problem include rough idling, jumpy or sluggish acceleration, poor fuel economy, and stalling. With the use of a throttle body cleaning product, the dirt and debris buildup are easily removed.

Is the throttle body sensor part of the throttle body?

What is a Throttle Position Sensor? The throttle position sensor is a vital part of the fuel management system installed on the throttle body. Its primary job is to ensure the correct mixture of fuel and air is delivered through the fuel injection system, through the intake, and into the combustion chamber.

How do you reset a throttle body?

Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.

Can you clean throttle body without removing it?

You don't need to remove a throttle body to clean it. If you have a DBW throttle body, DO NOT MOVE THE THROTTLE PLATE MANUALLY TO CLEAN IT, especially with the key in the ON position. ... Have them depress the gas pedal all the way to open the throttle plate so you can gain access to do your cleaning.

Does seafoam clean throttle body?

Sea Foam Spray is a blend of cleaning and lubricating petroleum ingredients that can be used SAFELY in all types of 2 and 4 stroke gasoline engines. ... Apply Sea Foam Spray through fuel injection throttle bodies to clean harmful engine deposits from intake valves and combustion chamber areas.

Will a bad throttle body throw a code?

a faulty tps can set a trouble code in the computer if the voltage value is either not present, sporadic, slow or constant, and this can illuminate your check engine light. 2.

What can cause a throttle body to go bad?

One of the main causes of a malfunctioning throttle body is internal contamination. Due to the contamination accumulated in the throttle body, the throttle valve can no longer move properly, causing problems with the control of the air supply.

What causes an electronic throttle control to go bad?

The most common causes of an electronic throttle control light are a faulty throttle control sensor or a faulty throttle accelerator pedal position sensor.

What happens when you unplug throttle position sensor?

The TPS as we call it is one of the most important sensors on the engine. Without it, the computer has no way of knowing when you push down on the gas or open the throttle. Best it can do it watch some other sensors and make some estimated guesses. On some cars, it may burp just as you unplug it if it's running.

How do I reset my Chevy throttle body?

Fully depress the accelerator pedal for 10 seconds. At this point the check engine light should change to blinking slowly indicating “Erasing ECU Memory”. 8. Release the accelerator pedal and turn the ignition switch to off.

How do you relearn a Nissan throttle body?

Turn the ignition switch on and wait 3 seconds. Immediately after the 3 seconds, the accelerator pedal must be pressed and released 5 times within 5 seconds. Wait 7 seconds and fully press the accelerator pedal and hold for approximately 20 seconds until the check engine light stops blinking and stays on.